Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Luray, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Hampton and the surrounding area.
Key Points
- ◦Benton Metal Depot is approximately 60.8 miles from Luray.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Luray is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
93
As of 2026 · Source |
Permits & Setbacks in Hampton County
Hampton treats a metal garage like any other accessory structure: under Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet, Hampton County Building & Planning Department typically doesn't require a full permit, but the Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup. setback rule still governs where it can sit on the lot.
Delivery to Luray
Current delivery time to Luray is approximately 1 to 2 weeks. Benton also serves nearby communities including Valentine, Solomons Crossroads, Gifford and Speaks Mill. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Hampton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Hampton County Building & Planning Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Do I need a permit for a metal garage in Luray?
That depends on the garage and the requirements of Hampton County Building & Planning Department. The current rule requires a permit once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Luray, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Luray before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Luray?
Current delivery time to Luray is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
Luray, Hampton County — At a Glance
- Permit Authority Name
- Hampton County Building & Planning Department
- Permit Authority Url
- https://www.hamptoncountysc.org/9/Building-Planning-Department
- Permit Threshold Sqft
- Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
- Setback Feet Side Rear
- Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
- Wind Load Zone
- Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 60.8
- Drive Minutes
- 93
- Nearby Towns
- Valentine, Solomons Crossroads, Gifford, Speaks Mill
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Luray, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Luray?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.hamptoncountysc.org/9/Building-Planning-Department (2026)
- https://www.hamptoncountysc.org/349/Ordinances — needs direct lookup (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Given/client spec — Hampton County is inland South Carolina (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Hampton County
See the Hampton County hub for metal garages
