Reviewed by the Benton Metal Depot team · Updated
For some residents in Nixville, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Hampton, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦The current local setback for a metal garage is Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Nixville, a building permit is required once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet.
- ◦Benton serves Speaks Mill, Lawtonville Crossroads, Lena and Estill and other communities around Nixville.
At a Glance
| Permit threshold |
Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
92
As of 2026 · Source |
Permits & Setbacks in Hampton County
Before a metal garage goes up in Nixville, check with Hampton County Building & Planning Department — Hampton's cutoff for requiring a building permit is Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet. Below that, you still need to clear the Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup. setback from your property line.
Delivery to Nixville
Residents in Nixville are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 57.1 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Hampton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Hampton County Building & Planning Department has requirements that can affect garage placement, including a current setback of Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Nixville?
That depends on the garage and the requirements of Hampton County Building & Planning Department. The current rule requires a permit once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Hampton County Building & Planning Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Nixville, Hampton County — At a Glance
- Permit Authority Name
- Hampton County Building & Planning Department
- Permit Authority Url
- https://www.hamptoncountysc.org/9/Building-Planning-Department
- Permit Threshold Sqft
- Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
- Setback Feet Side Rear
- Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
- Wind Load Zone
- Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 57.1
- Drive Minutes
- 92
- Nearby Towns
- Speaks Mill, Lawtonville Crossroads, Lena, Estill
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Nixville and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Nixville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.hamptoncountysc.org/9/Building-Planning-Department (2026)
- https://www.hamptoncountysc.org/349/Ordinances — needs direct lookup (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Given/client spec — Hampton County is inland South Carolina (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Hampton County
See the Hampton County hub for metal garages
