Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Yemassee, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Hampton and the surrounding area.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Delivery to Yemassee is currently estimated at 1 to 2 weeks.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 97.9 miles from Yemassee.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
119
As of 2026 · Source |
Permits & Setbacks in Hampton County
The permit question for a Yemassee metal garage comes down to one number from Hampton County Building & Planning Department: Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet. Stay under it and skip the full permit process; either way, keep the Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup. setback in mind before you pick a spot.
Delivery to Yemassee
Metal garage delivery to Yemassee can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Hampton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Yemassee, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How far is Benton Metal Depot from Yemassee?
Benton Metal Depot's Statesboro location is approximately 97.9 miles from Yemassee. The company serves residents throughout Hampton, including communities such as Hendersonville, Pocotaligo, McPhersonville and Brewton. Current delivery time for a metal garage to the Yemassee area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Yemassee is Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup., although you should confirm the requirement for your particular property with Hampton County Building & Planning Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Yemassee before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Yemassee?
Current delivery time to Yemassee is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Hampton County Building & Planning Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
Yemassee, Hampton County — At a Glance
- Permit Authority Name
- Hampton County Building & Planning Department
- Permit Authority Url
- https://www.hamptoncountysc.org/9/Building-Planning-Department
- Permit Threshold Sqft
- Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
- Setback Feet Side Rear
- Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
- Wind Load Zone
- Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 97.9
- Drive Minutes
- 119
- Nearby Towns
- Hendersonville, Pocotaligo, McPhersonville, Brewton
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Yemassee, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Yemassee?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.hamptoncountysc.org/9/Building-Planning-Department (2026)
- https://www.hamptoncountysc.org/349/Ordinances — needs direct lookup (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Given/client spec — Hampton County is inland South Carolina (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Hampton County
See the Hampton County hub for metal garages
