Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Clarking, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Charlton and the surrounding area.
Key Points
- ◦The current local setback for a metal garage is Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826)..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Clarking, a building permit is required once the garage exceeds Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet.
- ◦Benton serves Boggy, Toledo, Stokesville and Moniac and other communities around Clarking.
At a Glance
| Permit threshold |
Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
213
As of 2026 · Source |
Permits & Setbacks in Charlton County
Before a metal garage goes up in Clarking, check with Charlton County Building Inspections / Permitting & Code Enforcement — Charlton's cutoff for requiring a building permit is Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet. Below that, you still need to clear the Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826). setback from your property line.
Delivery to Clarking
Current delivery time to Clarking is approximately 1 to 2 weeks. Benton also serves nearby communities including Boggy, Toledo, Stokesville and Moniac. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Charlton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How far is Benton Metal Depot from Clarking?
Benton Metal Depot's Statesboro location is approximately 177.8 miles from Clarking. The company serves residents throughout Charlton, including communities such as Boggy, Toledo, Stokesville and Moniac. Current delivery time for a metal garage to the Clarking area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Clarking is Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826)., although you should confirm the requirement for your particular property with Charlton County Building Inspections / Permitting & Code Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Charlton County Building Inspections / Permitting & Code Enforcement has requirements that can affect garage placement, including a current setback of Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Clarking before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Clarking?
Current delivery time to Clarking is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
Clarking, Charlton County — At a Glance
- Permit Authority Name
- Charlton County Building Inspections / Permitting & Code Enforcement
- Permit Authority Url
- https://charltoncountyga.us/180/Permitting-Code-Enforcement
- Permit Threshold Sqft
- Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
- Setback Feet Side Rear
- Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
- Wind Load Zone
- Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 177.8
- Drive Minutes
- 213
- Nearby Towns
- Boggy, Toledo, Stokesville, Moniac
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Clarking, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Clarking?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://charltoncountyga.us/180/Permitting-Code-Enforcement (2026)
- https://library.municode.com/ga/charlton_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH150MAHOTR and https://charltoncountyga.us/182/Code-Enforcement-Building-Inspection (2026)
- https://library.municode.com/ga/charlton_county (zoning ordinance not independently located/verified) (2026)
- General ASCE 7 southeast-Georgia range (aggregated from secondary sources) — no county-specific or primary map source found; per county site, Charlton follows IBC 2018/IRC 2018 with Georgia Amendments (2026)
- Charlton County is not among the coastal counties named in the client spec (though it is in the far southeast corner of GA, bordering Florida, and closer to the coast than most inland counties) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
