Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Saint George? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Charlton, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Saint George is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 177.8 miles from Saint George.
At a Glance
| Permit threshold |
Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
213
As of 2026 · Source |
Permits & Setbacks in Charlton County
The permit question for a Saint George metal garage comes down to one number from Charlton County Building Inspections / Permitting & Code Enforcement: Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet. Stay under it and skip the full permit process; either way, keep the Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826). setback in mind before you pick a spot.
Delivery to Saint George
Residents in Saint George are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 177.8 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Charlton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Saint George, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How close can my metal garage be to the property line?
The current setback in Saint George is Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826)., although you should confirm the requirement for your particular property with Charlton County Building Inspections / Permitting & Code Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Saint George?
Benton Metal Depot's Statesboro location is approximately 177.8 miles from Saint George. The company serves residents throughout Charlton, including communities such as Clarking, Boggy, Toledo and Stokesville. Current delivery time for a metal garage to the Saint George area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Saint George?
Current delivery time to Saint George is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Saint George before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Charlton County Building Inspections / Permitting & Code Enforcement. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
Saint George, Charlton County — At a Glance
- Permit Authority Name
- Charlton County Building Inspections / Permitting & Code Enforcement
- Permit Authority Url
- https://charltoncountyga.us/180/Permitting-Code-Enforcement
- Permit Threshold Sqft
- Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
- Setback Feet Side Rear
- Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
- Wind Load Zone
- Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 177.8
- Drive Minutes
- 213
- Nearby Towns
- Clarking, Boggy, Toledo, Stokesville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Saint George and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Saint George?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://charltoncountyga.us/180/Permitting-Code-Enforcement (2026)
- https://library.municode.com/ga/charlton_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH150MAHOTR and https://charltoncountyga.us/182/Code-Enforcement-Building-Inspection (2026)
- https://library.municode.com/ga/charlton_county (zoning ordinance not independently located/verified) (2026)
- General ASCE 7 southeast-Georgia range (aggregated from secondary sources) — no county-specific or primary map source found; per county site, Charlton follows IBC 2018/IRC 2018 with Georgia Amendments (2026)
- Charlton County is not among the coastal counties named in the client spec (though it is in the far southeast corner of GA, bordering Florida, and closer to the coast than most inland counties) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
