Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Paxton, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Charlton.
Key Points
- ◦Benton Metal Depot is approximately 122.9 miles from Paxton.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Paxton is currently estimated at 1 to 2 weeks.
- ◦Benton serves Newell, Colerain, Mattox and Winokur and other communities around Paxton.
At a Glance
| Permit threshold |
Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
178
As of 2026 · Source |
Permits & Setbacks in Charlton County
The permit question for a Paxton metal garage comes down to one number from Charlton County Building Inspections / Permitting & Code Enforcement: Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet. Stay under it and skip the full permit process; either way, keep the Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826). setback in mind before you pick a spot.
Delivery to Paxton
The current estimate for getting a metal garage to Paxton is 1 to 2 weeks. The area is about 122.9 miles (178 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Charlton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Charlton County Building Inspections / Permitting & Code Enforcement has requirements that can affect garage placement, including a current setback of Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Do I need a permit for a metal garage in Paxton?
That depends on the garage and the requirements of Charlton County Building Inspections / Permitting & Code Enforcement. The current rule requires a permit once the garage exceeds Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Charlton County Building Inspections / Permitting & Code Enforcement. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Paxton, Charlton County — At a Glance
- Permit Authority Name
- Charlton County Building Inspections / Permitting & Code Enforcement
- Permit Authority Url
- https://charltoncountyga.us/180/Permitting-Code-Enforcement
- Permit Threshold Sqft
- Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
- Setback Feet Side Rear
- Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
- Wind Load Zone
- Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 122.9
- Drive Minutes
- 178
- Nearby Towns
- Newell, Colerain, Mattox, Winokur
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Paxton and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Paxton?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://charltoncountyga.us/180/Permitting-Code-Enforcement (2026)
- https://library.municode.com/ga/charlton_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH150MAHOTR and https://charltoncountyga.us/182/Code-Enforcement-Building-Inspection (2026)
- https://library.municode.com/ga/charlton_county (zoning ordinance not independently located/verified) (2026)
- General ASCE 7 southeast-Georgia range (aggregated from secondary sources) — no county-specific or primary map source found; per county site, Charlton follows IBC 2018/IRC 2018 with Georgia Amendments (2026)
- Charlton County is not among the coastal counties named in the client spec (though it is in the far southeast corner of GA, bordering Florida, and closer to the coast than most inland counties) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
