Reviewed by the Benton Metal Depot team · Updated
For some residents in Uptonville, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Charlton, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Delivery to Uptonville is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 122.9 miles from Uptonville.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦The current local setback for a metal garage is Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826)..
At a Glance
| Permit threshold |
Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
178
As of 2026 · Source |
Permits & Setbacks in Charlton County
Charlton treats a metal garage like any other accessory structure: under Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet, Charlton County Building Inspections / Permitting & Code Enforcement typically doesn't require a full permit, but the Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826). setback rule still governs where it can sit on the lot.
Delivery to Uptonville
Residents in Uptonville are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 122.9 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Charlton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Charlton County Building Inspections / Permitting & Code Enforcement. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Uptonville?
Benton Metal Depot's Statesboro location is approximately 122.9 miles from Uptonville. The company serves residents throughout Charlton, including communities such as Newell, Colerain, Mattox and Winokur. Current delivery time for a metal garage to the Uptonville area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Uptonville is Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826)., although you should confirm the requirement for your particular property with Charlton County Building Inspections / Permitting & Code Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Uptonville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Uptonville?
Current delivery time to Uptonville is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Uptonville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Charlton County Building Inspections / Permitting & Code Enforcement has requirements that can affect garage placement, including a current setback of Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
Uptonville, Charlton County — At a Glance
- Permit Authority Name
- Charlton County Building Inspections / Permitting & Code Enforcement
- Permit Authority Url
- https://charltoncountyga.us/180/Permitting-Code-Enforcement
- Permit Threshold Sqft
- Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
- Setback Feet Side Rear
- Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
- Wind Load Zone
- Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 122.9
- Drive Minutes
- 178
- Nearby Towns
- Newell, Colerain, Mattox, Winokur
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Uptonville, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Uptonville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://charltoncountyga.us/180/Permitting-Code-Enforcement (2026)
- https://library.municode.com/ga/charlton_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH150MAHOTR and https://charltoncountyga.us/182/Code-Enforcement-Building-Inspection (2026)
- https://library.municode.com/ga/charlton_county (zoning ordinance not independently located/verified) (2026)
- General ASCE 7 southeast-Georgia range (aggregated from secondary sources) — no county-specific or primary map source found; per county site, Charlton follows IBC 2018/IRC 2018 with Georgia Amendments (2026)
- Charlton County is not among the coastal counties named in the client spec (though it is in the far southeast corner of GA, bordering Florida, and closer to the coast than most inland counties) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
