Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Stokesville? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Charlton, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 177.8 miles from Stokesville.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Stokesville is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
213
As of 2026 · Source |
Permits & Setbacks in Charlton County
Charlton's permitting office, Charlton County Building Inspections / Permitting & Code Enforcement, sets the accessory-structure line at Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826). square feet — build under that and you generally skip the full building-permit process, though a setback of Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826). still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Stokesville
Residents in Stokesville are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 177.8 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Charlton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How close can my metal garage be to the property line?
The current setback in Stokesville is Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826)., although you should confirm the requirement for your particular property with Charlton County Building Inspections / Permitting & Code Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Stokesville?
Benton Metal Depot's Statesboro location is approximately 177.8 miles from Stokesville. The company serves residents throughout Charlton, including communities such as Clarking, Boggy, Toledo and Moniac. Current delivery time for a metal garage to the Stokesville area is about 1 to 2 weeks.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Stokesville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How long does it take to get a metal garage delivered to Stokesville?
Current delivery time to Stokesville is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Charlton County Building Inspections / Permitting & Code Enforcement. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Stokesville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
Stokesville, Charlton County — At a Glance
- Permit Authority Name
- Charlton County Building Inspections / Permitting & Code Enforcement
- Permit Authority Url
- https://charltoncountyga.us/180/Permitting-Code-Enforcement
- Permit Threshold Sqft
- Not found. The only published sqft figure on the county site is a 120 sq ft storage-building cap that applies narrowly to individual lots inside manufactured-home parks (Code of Ordinances Ch. 150), not a general residential/accessory permit exemption. Needs direct confirmation with Charlton County Building Inspections (912-496-3826).
- Setback Feet Side Rear
- Not found. No general accessory-structure setback table for residential/agricultural zoning districts was located on the county site or in the searchable Code of Ordinances. Needs direct confirmation with Charlton County Building Inspections/Code Enforcement (912-496-3826).
- Wind Load Zone
- Southeast Georgia coastal plain, inland but relatively close to the Atlantic (~35-40 miles) — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's inland range given proximity to the coast. NOT a verified figure; depends on which ASCE 7/IBC edition Charlton County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 177.8
- Drive Minutes
- 213
- Nearby Towns
- Clarking, Boggy, Toledo, Moniac
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Stokesville and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Stokesville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://charltoncountyga.us/180/Permitting-Code-Enforcement (2026)
- https://library.municode.com/ga/charlton_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH150MAHOTR and https://charltoncountyga.us/182/Code-Enforcement-Building-Inspection (2026)
- https://library.municode.com/ga/charlton_county (zoning ordinance not independently located/verified) (2026)
- General ASCE 7 southeast-Georgia range (aggregated from secondary sources) — no county-specific or primary map source found; per county site, Charlton follows IBC 2018/IRC 2018 with Georgia Amendments (2026)
- Charlton County is not among the coastal counties named in the client spec (though it is in the far southeast corner of GA, bordering Florida, and closer to the coast than most inland counties) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
