Reviewed by the Benton Metal Depot team · Updated
For some residents in Cedar Crossing, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Toombs, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦The current local setback for a metal garage is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Cedar Crossing, a building permit is required once the garage exceeds The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet.
- ◦Benton serves Rock Springs, English Eddy, McNatt Falls and Charles and other communities around Cedar Crossing.
At a Glance
| Permit threshold |
The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
101
As of 2026 · Source |
Permits & Setbacks in Toombs County
Toombs's permitting office, Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found), sets the accessory-structure line at The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet — build under that and you generally skip the full building-permit process, though a setback of Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311). still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Cedar Crossing
Current delivery time to Cedar Crossing is approximately 1 to 2 weeks. Benton also serves nearby communities including Rock Springs, English Eddy, McNatt Falls and Charles. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Toombs County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found) has requirements that can affect garage placement, including a current setback of Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Cedar Crossing?
That depends on the garage and the requirements of Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). The current rule requires a permit once the garage exceeds The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Cedar Crossing, Toombs County — At a Glance
- Permit Authority Name
- Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found)
- Permit Authority Url
- https://toombscountyga.gov/ordinances/building-permit-ordinance/
- Permit Threshold Sqft
- The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
- Setback Feet Side Rear
- Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 68.1
- Drive Minutes
- 101
- Nearby Towns
- Rock Springs, English Eddy, McNatt Falls, Charles
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Cedar Crossing and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Cedar Crossing?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (PDF not independently readable) (2026)
- No primary or secondary source located for Toombs County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Toombs County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Toombs County (Lyons/Vidalia area) is inland southeast Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
