Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in English Eddy can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Toombs and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Benton serves Rock Springs, Cedar Crossing, McNatt Falls and Charles and other communities around English Eddy.
- ◦In English Eddy, a building permit is required once the garage exceeds The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)..
At a Glance
| Permit threshold |
The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
101
As of 2026 · Source |
Permits & Setbacks in Toombs County
Toombs treats a metal garage like any other accessory structure: under The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet, Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found) typically doesn't require a full permit, but the Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311). setback rule still governs where it can sit on the lot.
Delivery to English Eddy
Current delivery time to English Eddy is approximately 1 to 2 weeks. Benton also serves nearby communities including Rock Springs, Cedar Crossing, McNatt Falls and Charles. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Toombs County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for English Eddy before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to English Eddy?
Current delivery time to English Eddy is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in English Eddy, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from English Eddy?
Benton Metal Depot's Statesboro location is approximately 68.1 miles from English Eddy. The company serves residents throughout Toombs, including communities such as Rock Springs, Cedar Crossing, McNatt Falls and Charles. Current delivery time for a metal garage to the English Eddy area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in English Eddy is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)., although you should confirm the requirement for your particular property with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
English Eddy, Toombs County — At a Glance
- Permit Authority Name
- Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found)
- Permit Authority Url
- https://toombscountyga.gov/ordinances/building-permit-ordinance/
- Permit Threshold Sqft
- The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
- Setback Feet Side Rear
- Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 68.1
- Drive Minutes
- 101
- Nearby Towns
- Rock Springs, Cedar Crossing, McNatt Falls, Charles
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in English Eddy and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in English Eddy?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (PDF not independently readable) (2026)
- No primary or secondary source located for Toombs County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Toombs County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Toombs County (Lyons/Vidalia area) is inland southeast Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
