Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in New Branch can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Toombs and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 48.5 miles from New Branch.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Delivery to New Branch is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
71
As of 2026 · Source |
Permits & Setbacks in Toombs County
Toombs treats a metal garage like any other accessory structure: under The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet, Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found) typically doesn't require a full permit, but the Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311). setback rule still governs where it can sit on the lot.
Delivery to New Branch
Residents in New Branch are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 48.5 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Toombs County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for New Branch before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to New Branch?
Current delivery time to New Branch is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from New Branch?
Benton Metal Depot's Statesboro location is approximately 48.5 miles from New Branch. The company serves residents throughout Toombs, including communities such as Ohoopee, Toombs Central, Ponderosa and Santa Claus. Current delivery time for a metal garage to the New Branch area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in New Branch is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)., although you should confirm the requirement for your particular property with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found) has requirements that can affect garage placement, including a current setback of Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
New Branch, Toombs County — At a Glance
- Permit Authority Name
- Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found)
- Permit Authority Url
- https://toombscountyga.gov/ordinances/building-permit-ordinance/
- Permit Threshold Sqft
- The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
- Setback Feet Side Rear
- Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 48.5
- Drive Minutes
- 71
- Nearby Towns
- Ohoopee, Toombs Central, Ponderosa, Santa Claus
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in New Branch and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in New Branch?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (PDF not independently readable) (2026)
- No primary or secondary source located for Toombs County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Toombs County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Toombs County (Lyons/Vidalia area) is inland southeast Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
