Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Toombs Central and across Toombs, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)..
- ◦Benton serves Ohoopee, New Branch, Ponderosa and Santa Claus and other communities around Toombs Central.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
71
As of 2026 · Source |
Permits & Setbacks in Toombs County
The permit question for a Toombs Central metal garage comes down to one number from Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found): The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311). setback in mind before you pick a spot.
Delivery to Toombs Central
The current estimate for getting a metal garage to Toombs Central is 1 to 2 weeks. The area is about 48.5 miles (71 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Toombs County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Toombs Central, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Toombs Central before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Toombs Central?
Current delivery time to Toombs Central is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from Toombs Central?
Benton Metal Depot's Statesboro location is approximately 48.5 miles from Toombs Central. The company serves residents throughout Toombs, including communities such as Ohoopee, New Branch, Ponderosa and Santa Claus. Current delivery time for a metal garage to the Toombs Central area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Toombs Central is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)., although you should confirm the requirement for your particular property with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Toombs Central, Toombs County — At a Glance
- Permit Authority Name
- Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found)
- Permit Authority Url
- https://toombscountyga.gov/ordinances/building-permit-ordinance/
- Permit Threshold Sqft
- The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
- Setback Feet Side Rear
- Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 48.5
- Drive Minutes
- 71
- Nearby Towns
- Ohoopee, New Branch, Ponderosa, Santa Claus
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Toombs Central and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Toombs Central?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (PDF not independently readable) (2026)
- No primary or secondary source located for Toombs County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Toombs County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Toombs County (Lyons/Vidalia area) is inland southeast Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
