Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Lyons? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Toombs, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton serves Ohoopee, New Branch, Toombs Central and Ponderosa and other communities around Lyons.
- ◦In Lyons, a building permit is required once the garage exceeds The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)..
At a Glance
| Permit threshold |
The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
71
As of 2026 · Source |
Permits & Setbacks in Toombs County
Toombs's permitting office, Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found), sets the accessory-structure line at The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet — build under that and you generally skip the full building-permit process, though a setback of Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311). still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Lyons
Current delivery time to Lyons is approximately 1 to 2 weeks. Benton also serves nearby communities including Ohoopee, New Branch, Toombs Central and Ponderosa. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Toombs County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Lyons?
That depends on the garage and the requirements of Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). The current rule requires a permit once the garage exceeds The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Lyons, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found) has requirements that can affect garage placement, including a current setback of Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How close can my metal garage be to the property line?
The current setback in Lyons is Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311)., although you should confirm the requirement for your particular property with Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Lyons, Toombs County — At a Glance
- Permit Authority Name
- Toombs County Commission (building permits administered per the county's Building Permit Ordinance; no separate named building department found)
- Permit Authority Url
- https://toombscountyga.gov/ordinances/building-permit-ordinance/
- Permit Threshold Sqft
- The Building Permit Ordinance PDF linked from the county site was not directly accessible to confirm a specific exemption threshold. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Toombs County specifically. Needs direct retrieval of the ordinance PDF or county contact.
- Setback Feet Side Rear
- Not found — no accessible zoning ordinance or setback table for Toombs County was locatable online. Needs direct confirmation with the Toombs County Commission (912-526-3311).
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 48.5
- Drive Minutes
- 71
- Nearby Towns
- Ohoopee, New Branch, Toombs Central, Ponderosa
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Lyons, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Lyons?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (2026)
- https://toombscountyga.gov/ordinances/building-permit-ordinance/ (PDF not independently readable) (2026)
- No primary or secondary source located for Toombs County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Toombs County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Toombs County (Lyons/Vidalia area) is inland southeast Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
